SOURCING HARD-TO-FIND PART NUMBERS
FROM ALL OVER THE WORLD
Special Offer
12 Mhz Crystal Oscillator | Quartz Crystal
₹10.00 (ex. GST)-
Buttons and Switches
6 Way SPST Slide DIP Switch – 2.54 mm Pitch
Product Details
- Product category: Switch
- Switch Type: 6 in 1 DIP SPST switch
- Pin type: DIP, PCB mounted
- Position or switch control: Individual
- No of position: 6
- Pin spacing: 2.54mm
- Actuator type: raised and recessed
- Color: red and white
- No of pins: 12
- Package contains: 1 x 6 in 1 dip switch
SKU: 37-1 -
1/4 Watt Resistors, Sensors and Modules
ROX5SSJ510R – 510 Ohms ±5% 5W Axial Flame Proof, Pulse Withstanding, Safety Metal Oxide Film Through Hole Resistor
1/4 Watt Resistors, Sensors and ModulesROX5SSJ510R – 510 Ohms ±5% 5W Axial Flame Proof, Pulse Withstanding, Safety Metal Oxide Film Through Hole Resistor
Product Details
- Resistor Type – General Purpose Resistor
- Element Type – Metal Oxide Film
- Operating Voltage – 500 V
- Power Rating – 5 W
- Resistance Class – Up to 1kΩ
- Resistance Value – 510 Ω
- Passive Component Tolerance – 5 %
- Lead Type – Axial-Leaded
- Brand – TE Internal
SKU: 1ohm-A111111 -
All
LM358DR Low Power Dual Op-Amp IC – SOIC-8 SMD Package
The LM358DR is a dual operational amplifier in an 8 pin SOIC package. It consists of two independent, high gain frequency compensated operational amplifiers designed to operate from a single supply or split supply over a wide range of voltages.SKU: n/a -
Diodes and Rectifiers
LM385 -1.2v TO-92 : 20mA Micropower Voltage Reference 3-Pin Diode
The LM385-1.2 integrated circuits is precision 1.2V shunt regulator diodes. These monolithic IC voltage references operate as a low-temperature-coefficient 1.2V zener with 0.2ohm dynamic impedance. A third terminal on the LM385-1.2 allows the reference voltage and temperature coefficient to be trimmed easily.
SKU: n/a -
-
Sensors and Modules
8 Channel 12V Relay Module
- Equipped with high-current relay 10A@250VAC / 10A@30VDC
- It can control both AC and DC appliances such as Solenoids, Motors, lights, fans etc.
- High-quality screw terminals (Terminal Block) provided (C, NC, NO) for quick and easy connection
- Freewheeling diode to protect your microcontroller
- Input Signal Pin connected to Burg stick for easy accessibility
Package contains: 1 piece of 8 channel relay module
SKU: 1250-1
-
Arduino and Accessories, Cables, Wires and Cables
1.4M A to B Male to Male USB Cable for Arduino
Product details
- Product type: USB Cable for Arduino Mega or Uno, Printer, scanner and any other peripherals to computer
- Used for: data transfer from computer to any other devices
- Colour: blue, transparent
- Length: 1m
- Data transfer: high speed and error free
- Connector type: A to B Male to Male
- Package contains: 1 X USB Cable for Arduino, printer, scanner etc
SKU: 28 -
-
-
-
Diodes and Rectifiers
GBJ2510 1000V 25A In-Line Bridge Rectifier
Product Details
- Product: GBJ2510 Bridge Rectifier
- Type: single phase bridge
- Polarity: marked
- Case/package: GBJ, molded plastic
- Number of pins: 4
- Mounting type: through hole
- Package contains: 1 x GBJ2510 Single Phase Bridge Rectifier
SKU: 404
Products Grid
Best Sellers
New Products
Battery Management System - BMS
3S 5A BMS Li-Ion Battery Protection Board
Product Type: BMS charger module
Suitable for: 18650 Li-Ion battery
No of cells compatible with 3
Short circuit protection: yes, delayed self-recovery
Dimension: 50mm x 9mm x 2mm
Package contains: 1 x 3s 5A Li-Ion BMS Protection PCB Board
SKU: DSM158
Arduino
Arduino Uno Prototyping Shield with 170 Point Mini Breadboard
Arduino Uno Protoshield directly fits into an Arduino UNO board and breaks out the I/O pins and makes it an expansion board. It makes it very easy to design any customer circuit. You can directly solder components on the board or connect the circuit using 170 point mini breadboard (included). The board is designed to solder both through-hole and SMD components to test them with your Arduino board. Although the SMD area is designed for 24 Pins SOIC integrated circuit and has a lot of space for TH components.
Features
It has a standard 0.1” x 0.1” prototyping grid with big pads
Comes with both stacking and plain header, choose whichever you want while soldering together
An IC pattern for adding a DIP IC up to 20 pins
Power rails down the middle and side
A reset button and an extra use button
2 3mm general use LEDs, red and green, as well as 2 matching resistors
A pass-thru ICSP stacking header so you can stack any kind of the shield on top, and/or use and AVR programmer
A surface-mount chip area for up to 14 SOIC size part
Compatible with tiny breadboards
Every pin is brought out
Gold plated pads
2 x 0.1uF ceramic capacitors on either side for extra power stability
SKU: BDA-002
Programmers
AVR USBASP Programmer For Arduino Raspberry-Pi Robotics
Product Specification
Package contains: unused 1 USBasp Programmer
Can work on many platforms like Linux, window, Mac etc.
There is no need for any external device or component
Gives speed up to 5KBP
Can programme many devices like, AVR, Raspberry PI, Arduino etc
Low cost and small size
Simple board of ATmega8 or ATmega88 and other passive components
SKU: 6