Special Offer
12 Mhz Crystal Oscillator | Quartz Crystal
₹10.00 (ex. GST)-
Arduino and Accessories, Sensors
Proximity Infrared Sensor Module Obstacle Detector IR Sensor for Arduino
Arduino and Accessories, SensorsProximity Infrared Sensor Module Obstacle Detector IR Sensor for Arduino
Product Specifications
- Module: IR Module
- Country of Origin: China
- Used in: Line tracking, heat detection, obstacle detection etc
- IC in module: LM358/LM393
- Package contains: checked and unused 1piece of IR Sensor Module
SKU: 1237 -
Voltage Regulators
LM7806 7806 6V Voltage Regulator IC
Product Details
- Product: 6V voltage regulator IC
- IC number: 7806
- Output current: 1.5A
- Input voltage: 10.5V to 25V
- Package type: TO-220
- No of pins: 3
- Mounting type: through hole
- Package contains: 1 x L7806 7806 IC 6V Voltage Regulator IC
SKU: 1052 -
Connectors, Wires and Cables, JST Relimate Connectors
5-pin JST Female Cable Connector 2.54mm 11-inch
Connectors, Wires and Cables, JST Relimate Connectors5-pin JST Female Cable Connector 2.54mm 11-inch
Product Details
- Product: JST XH Female connector
- Number of pins: 5-pin
- Connector pitch: 2.54mm
- Wire length: 25cm (11-inch)
- Package contains: 1 x 5-pin JST Female Cable Connector 2.54mm 11-inch
SKU: 183 -
-
Diodes and Rectifiers
KBPC3510 35A 1000V Single Phase Bridge Rectifier
Product Details
- Product: KBPC3510 single-phase rectifier
- Polarity: marked on the device
- Number of pins: 4
- Mounting: snap-on, wrap-around, solder, and PCB mounting
- Case: Metal
- Dimension: 29mm x 29mm x 11.5mm
- Package contains: 1 x KBPC3510
SKU: 305
Products Grid
Best Sellers
New Products
Battery Management System - BMS
3S 5A BMS Li-Ion Battery Protection Board
Product Type: BMS charger module
Suitable for: 18650 Li-Ion battery
No of cells compatible with 3
Short circuit protection: yes, delayed self-recovery
Dimension: 50mm x 9mm x 2mm
Package contains: 1 x 3s 5A Li-Ion BMS Protection PCB Board
SKU: DSM158
Arduino
Arduino Uno Prototyping Shield with 170 Point Mini Breadboard
Arduino Uno Protoshield directly fits into an Arduino UNO board and breaks out the I/O pins and makes it an expansion board. It makes it very easy to design any customer circuit. You can directly solder components on the board or connect the circuit using 170 point mini breadboard (included). The board is designed to solder both through-hole and SMD components to test them with your Arduino board. Although the SMD area is designed for 24 Pins SOIC integrated circuit and has a lot of space for TH components.
Features
It has a standard 0.1” x 0.1” prototyping grid with big pads
Comes with both stacking and plain header, choose whichever you want while soldering together
An IC pattern for adding a DIP IC up to 20 pins
Power rails down the middle and side
A reset button and an extra use button
2 3mm general use LEDs, red and green, as well as 2 matching resistors
A pass-thru ICSP stacking header so you can stack any kind of the shield on top, and/or use and AVR programmer
A surface-mount chip area for up to 14 SOIC size part
Compatible with tiny breadboards
Every pin is brought out
Gold plated pads
2 x 0.1uF ceramic capacitors on either side for extra power stability
SKU: BDA-002
Programmers
AVR USBASP Programmer For Arduino Raspberry-Pi Robotics
Product Specification
Package contains: unused 1 USBasp Programmer
Can work on many platforms like Linux, window, Mac etc.
There is no need for any external device or component
Gives speed up to 5KBP
Can programme many devices like, AVR, Raspberry PI, Arduino etc
Low cost and small size
Simple board of ATmega8 or ATmega88 and other passive components
SKU: 6